semiconductor technical data 2299 rev 5 ? motorola, inc. 1996 3/93 ! " the mc10h330 is a quad bus driver/receiver with twotoone output multiplexers. these multiplexers have a common select and output enable. when disabled, (oe = high) the bus outputs go to 2.0 v. their output can be brought to a low state (v ol ) by applying a high level to the receiver enable (re = high). the parameters specified are with 25 w loading on the bus drivers and 50 w loads on the receivers. ? propagation delay, 1.5 ns typical datatooutput ? improved noise margin 150 mv (over operating voltage and temperature range) ? voltage compensated ? mecl 10kcompatible maximum ratings characteristic symbol rating unit power supply (v cc = 0) v ee 8.0 to 0 vdc input voltage (v cc = 0) v i 0 to v ee vdc output current e continuous e surge i out 50 100 ma operating temperature range t a 0 to +75 c storage temperature range e plastic e ceramic t stg 55 to +150 55 to +165 c c electrical characteristics (v ee = 5.2 v 5%) (see note) 0 25 75 characteristic symbol min max min max min max unit power supply current i e e 157 e 143 e 157 ma input current high pins 58, 1720 pins 16, 21 pin 9 i inh e e e 667 514 475 e e e 417 321 297 e e e 417 321 297 m a input current low i inl 0.5 e 0.5 e 0.3 e m a high output voltage v oh 1.02 0.84 0.98 0.81 0.92 0.735 vdc low output voltage v ol 1.95 1.63 1.95 1.63 1.95 1.60 vdc high input voltage v ih 1.17 0.84 1.13 0.81 1.07 0.735 vdc low input voltage v il 1.95 1.48 1.95 1.48 1.95 1.45 vdc ac parameters propagation delay selecttoinput datatobus output selecttobus output oe tobus output bustoinput re toinput datatoreceiver input t pd 1.8 0.5 1.0 0.8 0.8 0.5 1.3 5.3 2.0 3.2 2.2 2.1 2.2 4.0 1.8 0.5 1.0 0.8 0.8 0.5 1.3 5.3 2.0 3.2 2.2 2.1 2.2 4.0 1.8 0.5 1.0 0.8 0.8 0.5 1.3 5.3 2.0 3.2 2.2 2.4 2.2 4.0 ns rise time t r 0.5 2.0 0.5 2.0 0.5 2.0 ns fall time t f 0.5 2.0 0.5 2.0 0.5 2.0 ns
dip pin assignment v cc x bus w bus v cc0 x1 x0 w1 w0 v cc0 y bus z bus oe y0 y1 z0 z1 24 23 22 21 20 19 18 17 1 2 3 4 5 6 7 8 s w in x in v ee re z in y in vcc0 16 15 14 13 9 10 11 12 note: each mecl 10h series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. the circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 ifpm is maintained. receiver outputs are terminated through a 50ohm resistor to 2.0 volts dc. bus outputs are terminated through a 25ohm resistor to 2.0 volts dc. l suffix ceramic package case 75802 p suffix plastic package case 72403 fn suffix plcc case 77602 pin assignment is for dualinline package. for plcc pin assignment, see the pin conversion tables on page 611 of the motorola mecl data book (dl122/d).
mc10h330 motorola mecl data dl122 e rev 6 2300 21 22 23 2 3 16 17 18 14 19 20 11 5 6 10 7 8 9 multiplexer truth table receiver truth table oe sw bus x bus y bus z bus re w in x in y in z in h l l x l h 2.0 v w0 w1 2.0 v x0 x1 2.0 v y0 y1 2.0 v z0 z1 h l l w bus l x bus l y bus l z bus v cc0 = pin 24 v cc = pin 1 v cc0 = pin 13 v cc0 = pin 4 v ee = pin 12 w1 w0 oe s re w bus x bus y bus z bus x1 x0 y1 y0 z1 z0 w in y in z in x in 15 logic diagram
mc10h330 2301 motorola mecl data dl122 e rev 6 outline dimensions fn suffix plastic plcc package case 77602 issue d notes: 1. datums l, m, and n determined where top of lead shoulder exits plastic body at mold parting line. 2. dimension g1, true position to be measured at datum t, seating plane. 3. dimensions r and u do not include mold flash. allowable mold flash is 0.010 (0.250) per side. 4. dimensioning and tolerancing per ansi y14.5m, 1982. 5. controlling dimension: inch. 6. the package top may be smaller than the package bottom by up to 0.012 (0.300). dimensions r and u are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 7. dimension h does not include dambar protrusion or intrusion. the dambar protrusion(s) shall not cause the h dimension to be greater than 0.037 (0.940). the dambar intrusion(s) shall not cause the h dimension to be smaller than 0.025 (0.635). n m l v w d d y brk 28 1 view s s lm s 0.010 (0.250) n s t s lm m 0.007 (0.180) n s t 0.004 (0.100) g1 g j c z r e a seating plane s lm m 0.007 (0.180) n s t t b s lm s 0.010 (0.250) n s t s lm m 0.007 (0.180) n s t u s lm m 0.007 (0.180) n s t z g1 x view dd s lm m 0.007 (0.180) n s t k1 view s h k f s lm m 0.007 (0.180) n s t dim min max min max millimeters inches a 0.485 0.495 12.32 12.57 b 0.485 0.495 12.32 12.57 c 0.165 0.180 4.20 4.57 e 0.090 0.110 2.29 2.79 f 0.013 0.019 0.33 0.48 g 0.050 bsc 1.27 bsc h 0.026 0.032 0.66 0.81 j 0.020 0.51 k 0.025 0.64 r 0.450 0.456 11.43 11.58 u 0.450 0.456 11.43 11.58 v 0.042 0.048 1.07 1.21 w 0.042 0.048 1.07 1.21 x 0.042 0.056 1.07 1.42 y 0.020 0.50 z 2 10 2 10 g1 0.410 0.430 10.42 10.92 k1 0.040 1.02
mc10h330 motorola mecl data dl122 e rev 6 2302 outline dimensions p suffix plastic dip package case 72403 issue d l suffix ceramic dip package case 75802 issue a c n k f g b 1 24 12 13 l p j seating plane dim a min max min max millimeters 1.240 1.285 31.50 32.64 inches b 0.285 0.305 7.24 7.75 c 0.160 0.200 4.07 5.08 d 0.015 0.021 0.38 0.53 f 0.045 0.062 1.14 1.57 g 0.100 bsc 2.54 bsc j 0.008 0.013 0.20 0.33 k 0.100 0.165 2.54 4.19 l 0.300 0.310 7.62 7.87 n 0.020 0.050 0.51 1.27 p 0.360 0.400 9.14 10.16 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of leads when formed parallel. 0.25 (0.010) m ta m d 24 pl t a notes: 1. chamfered contour optional. 2. dimension l to center of leads when formed parallel. 3. dimensioning and tolerancing per ansi y14.5m, 1982. 4. controlling dimension: inch. a b 24 13 12 1 t seating plane 24 pl k e f n c d g m a m 0.25 (0.010) t 24 pl j m b m 0.25 (0.010) t l m note 1 dim min max min max millimeters inches a 1.230 1.265 31.25 32.13 b 0.250 0.270 6.35 6.85 c 0.145 0.175 3.69 4.44 d 0.015 0.020 0.38 0.51 e 0.050 bsc 1.27 bsc f 0.040 0.060 1.02 1.52 g 0.100 bsc 2.54 bsc j 0.007 0.012 0.18 0.30 k 0.110 0.140 2.80 3.55 l 0.300 bsc 7.62 bsc m 0 15 0 15 n 0.020 0.040 0.51 1.01 motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. atypicalo parameters which may be provided in motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/affirmative action employer. how to reach us: usa / europe / locations not listed : motorola literature distribution; japan : nippon motorola ltd.; tatsumispdjldc, 6f seibubutsuryucenter, p.o. box 20912; phoenix, arizona 85036. 18004412447 or 6023035454 3142 tatsumi kotoku, tokyo 135, japan. 038135218315 mfax : rmfax0@email.sps.mot.com t ouchtone 6022446609 asia / pacific : motorola semiconductors h.k. ltd.; 8b tai ping industrial park, internet : http://designnet.com 51 ting kok r oad, tai po, n.t., hong kong. 85226629298 mc10h330/d ?
|
